<?xml version="1.0" encoding="UTF-8"?><toc><section id="foreword.nat"><title>Vorwort</title><section id="sub-amendments"><title>Änderungen</title></section><section id="sub-previous.edition"><title>Frühere Ausgaben</title></section></section><section id="sub-1"><label>1</label><title>Anwendungsbereich</title></section><section id="sub-2"><label>2</label><title>Normative Verweisungen</title></section><section id="sub-3"><label>3</label><title>Begriffe</title></section><section id="sub-4"><label>4</label><title>Symbole und Abkürzungen</title></section><section id="sub-5"><label>5</label><title>T-Nutenfräser mit Zylinderschaft</title><section id="sub-5.1"><label>5.1</label><title>Maße</title></section><section id="sub-5.2"><label>5.2</label><title>Ausführung</title></section></section><section id="sub-6"><label>6</label><title>Bezeichnung</title></section><section id="sub-7"><label>7</label><title>Maße und Toleranzen</title><section id="sub-7.1"><label>7.1</label><title>T-Nutenfräser mit Zylinderschaft</title></section><section id="sub-7.2"><label>7.2</label><title>Lauftoleranzen</title><section id="sub-7.2.1"><label>7.2.1</label><title>Prüfwerte</title></section><section id="sub-7.2.2"><label>7.2.2</label><title>Prüfung der Laufabweichungen</title></section></section></section><section id="sub-8"><label>8</label><title>Werkstoff und Härte</title><section id="sub-8.1"><label>8.1</label><title>Werkstoff</title><section id="sub-8.1.1"><label>8.1.1</label><title>Schneidteil</title></section><section id="sub-8.1.2"><label>8.1.2</label><title>Schaft</title></section></section><section id="sub-8.2"><label>8.2</label><title>Härte</title><section id="sub-8.2.1"><label>8.2.1</label><title>Schneidteil</title></section><section id="sub-8.2.2"><label>8.2.2</label><title>Schaft</title></section></section></section><section id="sub-9"><label>9</label><title>Ausführung</title><section id="sub-9.1"><label>9.1</label><title>Werkzeug-Anwendungsgruppe</title></section><section id="sub-9.2"><label>9.2</label><title>Schaft</title></section><section id="sub-9.3"><label>9.3</label><title>Schneid- und Drallrichtung</title></section><section id="sub-9.4"><label>9.4</label><title>Zentrierbohrungen</title></section><section id="sub-9.5"><label>9.5</label><title>Oberflächen</title><section id="sub-9.5.1"><label>9.5.1</label><title>Oberflächenrautiefen</title></section><section id="sub-9.5.2"><label>9.5.2</label><title>Oberflächenbehandlung</title></section></section><section id="sub-9.6"><label>9.6</label><title>Anzahl der Schneiden und Schneidengeometrie</title></section></section><section id="sub-10"><label>10</label><title>Kennzeichnung</title></section><section id="sub-annex.bibliography.nat"><title>Literaturhinweise (informativ)</title></section></toc>