<?xml version="1.0" encoding="UTF-8"?><toc><section id="foreword.nat"><title>Nationales Vorwort</title><section id="sub-d30762448e207"><title>Änderungen</title></section><section id="sub-d30762448e300"><title>Frühere Ausgaben</title></section></section><section id="foreword.reg"><title>Vorwort</title></section><section id="sub-endorsement.notice"><title>Anerkennungsnotiz</title></section><section id="sub-1"><label>1</label><title>Anwendungsbereich</title></section><section id="sub-2"><label>2</label><title>Normative Verweisungen</title></section><section id="sub-3"><label>3</label><title>Begriffe</title><section id="sub-3.1"><label>3.1</label><title>Allgemeines</title></section><section id="sub-3.2"><label>3.2</label><title>Bildlich erläuterte Begriffe</title><section id="sub-3.2.1"><label>3.2.1</label><title>Schneidprozess des Werkstückes</title></section><section id="sub-3.2.2"><label>3.2.2</label><title>fertiges Werkstück</title></section><section id="sub-3.2.3"><label>3.2.3</label><title>Schnittarten</title></section></section><section id="sub-3.3"><label>3.3</label><title>Schneidgeschwindigkeit</title></section><section id="sub-3.4"><label>3.4</label><title>Schnittfugenbreite</title></section><section id="sub-3.5"><label>3.5</label><title>Rillennachlauf</title></section><section id="sub-3.6"><label>3.6</label><title>Rechtwinkligkeits- oder Neigungstoleranz</title></section><section id="sub-3.7"><label>3.7</label><title>Höhendifferenz des Profilelements</title></section><section id="sub-3.8"><label>3.8</label><title>gemittelte Rauhtiefe</title></section><section id="sub-3.9"><label>3.9</label><title>Anschmelzung</title></section><section id="sub-3.10"><label>3.10</label><title>Kolkung</title></section></section><section id="sub-4"><label>4</label><title>Symbole und Maßbuchstaben</title></section><section id="sub-5"><label>5</label><title>Form- und Lagetoleranz</title></section><section id="sub-6"><label>6</label><title>Ermittlung der Qualität von Schnittflächen</title><section id="sub-6.1"><label>6.1</label><title>Allgemeines</title></section><section id="sub-6.2"><label>6.2</label><title>Messen</title><section id="sub-6.2.1"><label>6.2.1</label><title>Messbedingungen</title></section><section id="sub-6.2.2"><label>6.2.2</label><title>Messstellen</title><section id="sub-6.2.2.1"><label>6.2.2.1</label><title>Allgemeines</title></section><section id="sub-6.2.2.2"><label>6.2.2.2</label><title>Anzahl der Messstellen</title></section><section id="sub-6.2.2.3"><label>6.2.2.3</label><title>Lage der Messstellen</title></section></section><section id="sub-6.2.3"><label>6.2.3</label><title>Ausführung</title></section></section></section><section id="sub-7"><label>7</label><title>Qualität der Schnittfläche</title><section id="sub-7.1"><label>7.1</label><title>Kenngrößen</title></section><section id="sub-7.2"><label>7.2</label><title>Messbereiche</title><section id="sub-7.2.1"><label>7.2.1</label><title>Allgemeines</title></section><section id="sub-7.2.2"><label>7.2.2</label><title>Rechtwinkligkeits- oder Neigungstoleranz </title></section><section id="sub-7.2.3"><label>7.2.3</label><title>Gemittelte Rauhtiefe </title></section></section></section><section id="sub-8"><label>8</label><title>Maßtoleranzen</title><section id="sub-8.1"><label>8.1</label><title>Allgemeines</title></section><section id="sub-8.2"><label>8.2</label><title>Maßtoleranzen bei Teilen ohne Nachbearbeitung</title></section><section id="sub-8.3"><label>8.3</label><title>Maßtoleranzen bei Teilen mit Nachbearbeitung</title><section id="sub-8.3.1"><label>8.3.1</label><title>Allgemeines</title></section><section id="sub-8.3.2"><label>8.3.2</label><title>Bearbeitungszugabe</title></section></section></section><section id="sub-9"><label>9</label><title>Bezeichnung</title></section><section id="sub-10"><label>10</label><title>Angaben in technischen Unterlagen</title><section id="sub-10.1"><label>10.1</label><title>Maßangaben</title></section><section id="sub-10.2"><label>10.2</label><title>Angabe der Schnittqualität und der Toleranzklasse</title><section id="sub-10.2.1"><label>10.2.1</label><title>In technischen Zeichnungen</title></section><section id="sub-10.2.2"><label>10.2.2</label><title>Im Schriftfeld technischer Unterlagen</title></section></section></section><section id="sub-a"><label>Anhang A</label><title>Erreichbare Schnittqualitäten für die unterschiedlichen Schneidprozesse (informativ)</title></section><section id="sub-b"><label>Anhang B</label><title>Prozessgrundlagen (informativ)</title><section id="sub-b.1"><label>B.1</label><title>Allgemeines</title></section><section id="sub-b.2"><label>B.2</label><title>Einteilung nach der Physik des Schneidverfahrens</title><section id="sub-b.2.1"><label>B.2.1</label><title>Brennschneiden</title></section><section id="sub-b.2.2"><label>B.2.2</label><title>Schmelzschneiden</title></section><section id="sub-b.2.3"><label>B.2.3</label><title>Sublimierschneiden</title></section></section><section id="sub-b.3"><label>B.3</label><title>Prozesse</title><section id="sub-b.3.1"><label>B.3.1</label><title>Autogenes Brennschneiden</title></section><section id="sub-b.3.2"><label>B.3.2</label><title>Plasmaschneiden</title></section><section id="sub-b.3.3"><label>B.3.3</label><title>Laserstrahlschneiden</title></section></section><section id="sub-b.4"><label>B.4</label><title>Werkstoffe</title><section id="sub-b.4.1"><label>B.4.1</label><title>Autogenes Brennschneiden</title></section><section id="sub-b.4.2"><label>B.4.2</label><title>Plasmaschneiden</title></section><section id="sub-b.4.3"><label>B.4.3</label><title>Laserstrahlschneiden</title></section></section></section><section id="sub-bibliography.int"><title>Literaturhinweise (informativ)</title></section><section id="sub-za"><label>Anhang ZA</label><title>Abschnitte in dieser Europäischen Norm, die grundlegende Anforderungen oder andere Vorgaben von EU-Richtlinien betreffen (informativ)</title></section></toc>