1.1 This practice sets forth criteria for the design, manufacture, assembly, modification, operation, maintenance, service, or repair of plant-based and mobile secure destruction equipment. 1.2 ...

1.1 This practice covers a procedure for developing precautionary labels for art materials and provides hazard and precautionary statements based upon knowledge that exists in the scientific and ...

1.1 These test methods cover the determination of the operating capacity of particulate cation-exchange materials when used for the removal of calcium, magnesium, and sodium ions from water. It is ...

1.1 This specification covers the magnetic properties of 50 nickel-50 iron parts fabricated by powder metallurgy techniques and is intended for parts that require high magnetic permeability, high ...

1.1 This specification covers the manufacture and acceptance of reinforced precast concrete end sections for pipe, herein referred to as "end section(s)," to conform to the owner's requirements.

1.1 This specification provides the minimum specification for use of non metallic plaster bases with Portland cement based plaster. 1.2 Units- The values stated in either SI units or inch-pound ...

1.1 This specification covers reinforced concrete pipe intended to be used for the construction of pressure pipelines with low internal hydrostatic heads generally not exceeding 125 ft. 1.2 This ...

1.1 This test method covers determination of the air content of freshly mixed concrete from observation of the change in volume of concrete with a change in pressure. 1.2 This test method is ...

1.1 This terminology refers to the terms relating to lime and limestone products as used by the industry. 1.2 Where appropriate, the various terms defined below should be prefixed with one or ...

1.1 This test method measures the resistance to slippage of warp yarns over filling yarns, or filling yarns over warp yarns, in woven upholstery fabrics, using a specific standard seam assembly by ...

1.1 This test method determines the snagging resistance of a fabric. 1.2 Studies of fabric snagging have shown that this test method is suitable for a range of woven and knitted fabrics made from ...

1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene ...

1.1 This test method covers determining the density of freshly mixed pervious concrete under standardized conditions and gives formulas for calculating the void content of pervious concrete. Test ...

1.1 This test method covers the determination of flexural toughness of fiber-reinforced concrete expressed as energy absorption in the post-crack range using a round panel supported on three ...

1.1 This practice identifies and defines the duties, responsibilities, and minimum technical requirements of testing agency personnel and the minimum technical requirements for equipment utilized ...

1.1 This descriptive nomenclature is intended to give accurate descriptions of some common or important naturally occurring and synthetic constituents of high-density aggregates for ...

1.1 This specification covers special aggregates and high-density aggregates for use in radiation-shielding concretes or other applications in which composition or high-density, or both, are of ...

1.1 This test method covers the determination of the relative quantity of mixing water that will bleed from a sample of freshly mixed concrete. 1.2 When various concretes are to be compared, if ...

1.1 This practice covers procedures for making and curing cylinder and beam specimens from representative samples of fresh concrete for a construction project. 1.2 This practice is not intended ...

1.1 This test method 2 describes the determination of the concentration of fibers, expressed as the number of such fibers (f) per cubic centimeter (millilitre) of air, using phase contrast ...

1.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GNSS 2 receiver to navigate on land and small bodies of water. 1.2 This guide applies to the use of a GNSS ...

1.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GNSS 2 receiver to determine one's position and collect location data in wilderness and non-wilderness ...

1.1 This specification covers minimum requirements for hazard mitigation in propulsion systems installed on small aeroplanes. 1.2 The applicant for a design approval must seek the individual ...

1.1 This test method covers procedures for determining the internal shear resistance of a geosynthetic clay liner (GCL) or the interface shear resistance between the GCL and an adjacent material ...

1.1 This practice covers procedures to be followed for direct exposure of house and trim paints on new, previously unpainted wood and wood composite materials to the environment. When originators ...

1.1 This practice is applicable to sampling gaseous uranium hexafluoride (UF 6 ), depleted, natural or enriched in 235U, from processing facilities, isotope enrichment cascades or storage ...

1.1 This fire-test-response test method covers the determination under specified laboratory conditions of the combustibility of building materials. Materials passing this test are typically ...

1.1 This specification covers the minimum requirements for field and laboratory personnel, for establishing and maintaining a quality management system, and establishes minimum qualifications for ...

1.1 This specification covers airworthiness requirements for the design of a powered or non-powered fixed wing light sport aircraft, a "glider." 1.2 A glider for the purposes of this specification ...

1.1 This specification covers airworthiness requirements for the design of powered fixed wing light sport aircraft, an "airplane." 1.2 Units- The values given in this standard are in SI units and ...

1.1 This specification covers the requirement for installing oxygen systems in light sport aircraft. 1.2 This standard does not purport to address all of the safety concerns, if any, associated ...

1.1 This specification establishes requirements common to wrought copper and copper alloy wire and shall apply to Specifications B16/B16M , B99/B99M , B134/B134M , B159/B159M , B197/B197M ...

1.1 This specification 2 establishes requirements for seamless red brass (Copper Alloy UNS No. C23000) 3 pipe in nominal pipe sizes, both regular and extra-strong. In the annealed temper (O61) ...

1.1 This specification 2 establishes the requirements for copper conductor bar, rod, and shapes for electrical (bus) applications and rod, bar, and shapes for general applications. 1.1.1 The ...

1.1 This test method covers a procedure to determine the water-in-oil emulsification tendencies and stabilities in the laboratory. The results of this test method can provide oil behavior data for ...