This procedure is used to test and evaluate the resistance of fastener surface finishes to laboratory salt spray testing.

This specification covers performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical ...

The procedures contained in this specification cover the laboratory testing of miniature incandescent bulbs for use in automotive illumination and signaling applications. The following tests shall ...

This standard outlines the conditions that enhance the risk of hydrogen embrittlement of steel and defines the relief procedures required to minimize the risk of hydrogen embrittlement. It is ...

This standard sets forth the performance and durability requirements for 12-volt, D.C. brush-type electric motors used for automobile Heating, Ventilation, and Air Conditioning (HVAC) blowers and ...

This standard outlines test methods and practices which can detect embrittlement of steel parts. It is a process control or referee verification test. The risk of embrittlement of steel is ...

This specification covers the grain flow pattern requirements in headed bolts, screws, and studs. The heading practice in the manufacture of the bolt, screw, or stud sets the grain flow pattern ...

The materials defined by this U.S. Car/SAE Recommended Practice are low VOC water based coatings for automotive tooling and general maintenance.

This standard provides a test method for determining the torque-tension relationship of both external and internal metric threaded fasteners for the purpose of measuring the frictional ...

This standard provides a test method for determining the torque-tension relationship of a fastener finish as applied to a surrogate screw for the purpose of measuring the frictional characteristic ...

This document gives specific and measurable design requirements to be applied at a design review prior to tooling. The specification is formatted as a checklist to aid in its use. The requirements ...

This standard covers the operational characteristics, environment, durability procedures, and test procedures for in-tank electric fuel pumps for automotive gasoline applications. Specific ...

The procedures contained in this specification cover the laboratory testing of replaceable halogen incandescent bulbs for use in automotive road illumination. The following tests are intended to ...

This specification establishes the requirements and test procedures for automotive miniature bulb retention devices, including wedge base sockets with integral connectors, direct wire wedge base ...

This document contains procedures for testing performance of SMB-style electrical terminals, connectors, and components for coaxial cable connection systems intended for road vehicle applications.

This document is a supplement to SAE/USCAR 17 and is intended to give recommended usages for one and two-way RF connectors and dimensional requirements for 2-way RF connectors and hybrid (RF & DC ...

This radio frequency (RF) connector interface specification is suited for unsealed automobile applications up to 2 GHz. Dimensional requirements are specified in this document to ensure ...

This radio frequency (RF) connector interface specification is suited for unsealed automobile applications up to 2 GHz.Dimensional requirements are specified in this document to ensure ...

This life test for underhood/passenger/trunk connector systems may be used in place of Section 5.9.6, Connection System Electrical Table of SAE/USCAR-2. All other requirements of SAE/USCAR-2 ...

This specification defines test methods and requirements for validation of solderless crimped connections. The purpose of this test is to simulate in the lab the stress seen in a typical life (15 ...

This International Standard specifies the dimensions, test methods, and requirements for single core 60 V cables intended for use in road vehicle applications where the nominal system voltage is ...

This specification establishes the performance and validation requirements for the inflator assembly used in airbag modules.

This document decribes the deign relative to assembly force, and hand clearance guidelines for conventional hand-plug, mechanical assist and twist lock electrical connectors, as well as Connector ...

This test procedure is intended to evaluate and/or validate electrical ground schemes for use on the body or chassis. There are two classes based on the expected environmental conditions. Exposed ...

This specification is a general level subsystem light source specification that establishes test requirements of a Gas Discharge Light Source (GDLS) subsystem for use on passenger vehicles.

This specification establishes the design, performance, and validation requirements for the initiator assembly used in airbag modules, seatbelt pretensioners and/or any other Electro-Explosive ...

This document specifies dimensional, functional and visual requirements for Automotive grade coaxial cable. This material will be designated AG for general-purpose automotive applications or AG LL ...

Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of any USB cable assemblies and associated ...

This standard lists variables that shall be investigated and reported as an initial investigation into new or revised surface finishes intended for use on fasteners. This standard provides ...

This specification is a general level subsystem light source specification that establishes test requirements of light emitting diode (LED) components and modules for use in automotive lighting ...

The procedures contained in this specification cover the laboratory testing of Exterior Lamps for use in automotive road illumination. The following tests are intended to be run under the ...

A bolt-load retention (BLR) test is a practical test to determine the bolt load of a fastener joint with time and at given temperatures. There are three types of BLR tests described in this ...

This specification defines the dimensional and performance requirements for aftermarket spin-on oil filters intended for use on gasoline engines. Filters meeting this specification may also be ...

Procedures included within this specification supplement are, when used in conjunction with SAE/USCAR 2, intended to cover performance testing at all phases of development, production, and field ...

This specification defines test methods and performance criteria for ultrasonically welded wire-to-terminal bonds as shown in Figure 1. This specification subjects parts to environmental exposures ...

This standard describes a requirement for automotive tire traceability. It includes a definition of the RFID tag and the associated tire data set that can be accessed using the RFID tag as an ...

This guideline is applicable to existing lead solder production products that will change to lead-free solder processes to meet the ELV Directive 2000/53/EC Annex II, exemption 8B requirements.

This document describes the assessment methods and physical requirements associated with the manual handling of carts and dollies, specific to material handling systems. All possible designs and ...

This document describes the design, assessment methods and physical requirements associated with material handling systems. This would include, but not limited to manual dollies, small lot systems ...

This document describes the design and assembly force guidelines for conventional shipping caps, torque caps, and body plugs. All possible design and applications could not be anticipated in ...

This specification describes a method and acceptance criteria for testing automotive wire harness retainer clips. Retainer clips are plastic parts that hold a wire harness or electrical connector ...

SAE/USCAR-45 defines test methods and performance requirements for ultrasonically-welded wire-to-wire splices for automotive applications. Face-to-face, butt splice, and center strip ...

SAE/USCAR-46 defines test methods and outputs for engine oil pump bench testing. Performance and durability testing are the primary focus of this standard. This is written to specifically address ...

This document describes the assembly force guidelines for manually seated push-pins, clips, and similar retention devices. For the purpose of this document, the term "clip" is used to reference ...

This specification establishes the minimum required performance and validation for the seatbelt pyrotechnic pretensioners integrated into retractors, buckles, and/or anchors. It also includes pyro ...

This document contains procedures for performance testing of electrical terminals, connectors, and components for coaxial-style cable with an outside cable diameter of 3.6 mm and smaller. These ...

This specification establishes the DV/PV performance and validation requirements for frontal airbag modules, namely driver, passenger, and knee airbags. In cases where airbag designs fall outside ...

The provisions of this document, attachments, and supplements apply to the creation of a universal methodology for data communication, machine language, and reporting to and from manufacturing ...