SAE J-Standards (Ground Vehicle Standards)

2,132 search results

Sort by:
  • Two-Stroke-Cycle Gasoline Engine Lubricants Performance and Service Classification

    Standard [CURRENT] 2025-01-21

    SAE J 2116:2025-01-21

    Two-Stroke-Cycle Gasoline Engine Lubricants Performance and Service Classification

    This SAE Standard was prepared by Technical Committee 1, Engine Lubrication, of SAE Fuels and Lubricants Council. The intent is to improve communications among engine manufacturers, engine users ...

    Accessibility

    84.50 EUR VAT included

    78.97 EUR VAT excluded

    To selection
  • Braking Performance - Asphalt Pavers

    Standard [CURRENT] 2024-08-12

    SAE J 2118:2024-08-12

    Braking Performance - Asphalt Pavers

    This SAE Standard specifies brake system performance and test criteria to enable uniform evaluation of the braking capability of self-propelled, rubber-tired and tracked asphalt pavers. Service ...

    Accessibility

    96.30 EUR VAT included

    90.00 EUR VAT excluded

    To selection
  • Manual Controls for Mature Drivers

    Standard [CURRENT] 1997-10-01

    SAE J 2119:1997-10-01

    Manual Controls for Mature Drivers

    Since little data exists to provide appropriate values for control parameters that would be appropriate for mature drivers, the following recommendations are of a general nature. However, they are ...

    Accessibility

    84.50 EUR VAT included

    78.97 EUR VAT excluded

    To selection
  • Personal Watercraft - Electrical Systems

    Standard [CURRENT] 2023-02-20

    SAE J 2120:2023-02-20

    Personal Watercraft - Electrical Systems

    This SAE Standard establishes a uniform test procedure and performance requirements for the electrical system in personal watercraft. This SAE Standard does not apply to outboard powered personal ...

    Accessibility

    91.00 EUR VAT included

    85.05 EUR VAT excluded

    To selection
  • Requirements for Composite Lighting Assemblies Used on Construction and Industrial Machinery

    Standard [CURRENT] 2023-07-12

    SAE J 2121:2023-07-12

    Requirements for Composite Lighting Assemblies Used on Construction and Industrial Machinery

    This SAE Standard provides general design performance requirements and related test procedures for composite lighting unit assemblies, other than signaling and marking devices, used on earthmoving ...

    Accessibility

    107.00 EUR VAT included

    100.00 EUR VAT excluded

    To selection
  • Numbering System for Single Diameter Drills

    Standard [CURRENT] 2019-10-09

    SAE J 2122:2019-10-09

    Numbering System for Single Diameter Drills

    This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools.

    Accessibility

    126.30 EUR VAT included

    118.04 EUR VAT excluded

    To selection
  • Numbering System for Taps

    Standard [CURRENT] 2019-10-09

    SAE J 2123:2019-10-09

    Numbering System for Taps

    This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, and Metric sizes up to ...

    Accessibility

    126.30 EUR VAT included

    118.04 EUR VAT excluded

    To selection
  • Numbering System for Single Diameter and Taper Reamers

    Standard [CURRENT] 2019-10-09

    SAE J 2124:2019-10-09

    Numbering System for Single Diameter and Taper Reamers

    This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools.

    Accessibility

    132.70 EUR VAT included

    124.02 EUR VAT excluded

    To selection
  • Guidelines for Requests Received from Outside Sources for the CONAG Council to Originate or Review Technical Reports

    Standard [CURRENT] 2015-03-27

    SAE J 2129:2015-03-27

    Guidelines for Requests Received from Outside Sources for the CONAG Council to Originate or Review Technical Reports

    This SAE Information Report lists the method which outside sources will follow when submitting documents for origination or review by the SAE CONAG Council.

    Accessibility

    80.30 EUR VAT included

    75.05 EUR VAT excluded

    To selection
  • Identification of Self-Propelled Sweepers and Cleaning Equipment Part 1 - Machines with a Gross Vehicle Mass Greater than 5000 kg

    Standard [CURRENT] 2021-07-20

    SAE J 2130/1:2021-07-20

    Identification of Self-Propelled Sweepers and Cleaning Equipment Part 1 - Machines with a Gross Vehicle Mass Greater than 5000 kg

    This SAE Standard applies to all self-propelled machines with a gross vehicle mass greater than 5000 kg that are utilized to clean material from highways, parking lots, airfield runways, outside ...

    Accessibility

    84.50 EUR VAT included

    78.97 EUR VAT excluded

    To selection
Note

If you leave this page your selected items will not be added to the selection. What do you want to do next?

Discard selection and go to the next page