SAE J-Standards (Ground Vehicle Standards)

2,131 search results

Standard [CURRENT] 2026-01-27

SAE J 2998:2026-01-27

Model Description Documentation Recommended Practice for Ground Vehicle System and Subsystem Simulation

SAE J2998 defines the recommended information content to be included for documenting dynamical models used for simulation of ground vehicle systems. It describes the information that should be ...

203.30 EUR VAT included

190.00 EUR VAT excluded
To selection
Standard [CURRENT] 2026-04-13

SAE J 2999:2026-04-13

Determination of the Effective Projected Luminous Lens Area (EPLLA) by Design Analysis

This SAE Recommended Practice provides a method for determining the Effective Projected Luminous Lens Area (EPLLA) of a lamp function using design analysis. This standard was created to clarify ...

84.50 EUR VAT included

78.97 EUR VAT excluded
To selection
Standard [CURRENT] 2024-08-12

SAE J 3001:2024-08-12

Brake Insulator Damping Measurement Procedure

This procedure is applicable to modes from 500 Hz and 13000 Hz. The parameters measured with this procedure are defined as the damping factor, ξ, for the first nine vibration modes of the beam.

96.30 EUR VAT included

90.00 EUR VAT excluded
To selection
Standard [CURRENT] 2021-01-27

SAE J 3002:2021-01-27

Disc and Drum Brake Dynamometer Low-Frequency Noise Test Procedure

This test procedure outlines the necessary test equipment (test fixture, dynamometer, data acquisition system, etc.) and test sequence required to test for low-frequency brake noise (200 Hz to ...

119.80 EUR VAT included

111.96 EUR VAT excluded
To selection
Standard [CURRENT] 2017-11-16

SAE J 3003:2017-11-16

Dimensional Specifications for General Service Sealed Lighting Units

80.30 EUR VAT included

75.05 EUR VAT excluded
To selection
Standard [CURRENT] 2019-02-21

SAE J 3005/1:2019-02-21

Permanently or Semi-Permanently Installed Diagnostic Communication Devices

The scope of the document is to define communication best practices in order to minimize problems for the vehicle owner when installing equipment which has a permanently or semi-permanently ...

153.00 EUR VAT included

142.99 EUR VAT excluded
To selection
Standard [CURRENT] 2020-03-04

SAE J 3005/2:2020-03-04

Permanently or Semi-Permanently Installed Diagnostic Communication Devices, Security Guidelines

The scope of the document is to define the cyber-security best practices to reduce interference with normal vehicle operation, or to minimize risk as to unauthorized access of the vehicle's ...

138.00 EUR VAT included

128.97 EUR VAT excluded
To selection
Standard [CURRENT] 2024-12-03

SAE J 3006:2024-12-03

Low-Duty Inertia Dynamometer Hydraulic Brake Wear Test Procedures for Vehicles Above 4536 kg (10000 pounds) of GVWR

This Recommended Practice is derived from OEM and tier-1 laboratory tests and applies to two-axle multipurpose passenger vehicles, or trucks with a GVWR above 4536 kg (10000 pounds) equipped with ...

135.90 EUR VAT included

127.01 EUR VAT excluded
To selection
Standard [CURRENT] 2026-05-27

SAE J 3007:2026-05-27

Top Speed Test Procedure for Electric Motorcycles

This SAE Recommended Practice incorporates a track-based test procedure that produces a representative value for vehicle top speed when operating on a level paved road with a fully charged battery.

111.30 EUR VAT included

104.02 EUR VAT excluded
To selection
Standard [CURRENT] 2023-07-19

SAE J 3008:2023-07-19

Sealed Trailer Tow Connector

This SAE Standard provides the auxiliary requirements for automotive or RV, additional 12 position, sealed Trailer Tow Connector Plug and Receptacle. The information included within this ...

132.70 EUR VAT included

124.02 EUR VAT excluded
To selection

Note

If you leave this page your selected items will not be added to the selection. What do you want to do next?

Discard selection and go to the next page