Maschinenbau und Messwesen

7 search results

Sort by:
  • I++ DME - Dimensional Measurement Equipment Interface (Version 2.5)

    Technical rule [CURRENT] 2024-04

    VDMA 8722:2024-04

    I++ DME - Dimensional Measurement Equipment Interface (Version 2.5)

    from 157.00 EUR VAT included

    from 146.73 EUR VAT excluded

    To selection
  • Standard Tables of Body Measurements for Adult Male, Chest Size Range 34 – 52 Short, Regular, and Tall

    Standard [CURRENT] 2024

    ASTM D 6240/D 6240Ma:2024

    Standard Tables of Body Measurements for Adult Male, Chest Size Range 34 – 52 Short, Regular, and Tall

    1.1 These tables list body measurements of adult male figure type, chest sizes 34 through 52 in Short, Regular, and Tall. Although these are body measurements, they can be used as a baseline in ...

    from 73.80 EUR VAT included

    from 68.97 EUR VAT excluded

    To selection
  • Standard Guide for Conducting Borehole Geophysical Logging - Gamma

    Standard [CURRENT] 2018

    ASTM D 6274:2018

    Standard Guide for Conducting Borehole Geophysical Logging - Gamma

    This guide covers the general procedures necessary to conduct gamma, natural gamma, total count gamma, or gamma ray (hereafter referred to as gamma) logging of boreholes, wells, access tubes ...

    from 81.30 EUR VAT included

    from 75.98 EUR VAT excluded

    To selection
  • Standard Test Method for Determination of the Linear Coefficient of Thermal Expansion of Plastic Lumber and Plastic Lumber Shapes Between –30 and 140°F (–34.4 and 60°C)

    Standard [CURRENT] 2021

    ASTM D 6341:2021

    Standard Test Method for Determination of the Linear Coefficient of Thermal Expansion of Plastic Lumber and Plastic Lumber Shapes Between –30 and 140°F (–34.4 and 60°C)

    1.1 This test method covers the determination of the coefficient of linear thermal expansion for plastic lumber and plastic lumber shapes to two significant figures. The determination is made by ...

    from 73.80 EUR VAT included

    from 68.97 EUR VAT excluded

    To selection
  • Standard Test Method for Evaluating the Performance of Systems that Measure Static, Six Degrees of Freedom (6DOF), Pose

    Standard [CURRENT] 2022

    ASTM E 2919:2022

    Standard Test Method for Evaluating the Performance of Systems that Measure Static, Six Degrees of Freedom (6DOF), Pose

    1.1 Purpose- In this test method, metrics and procedures for collecting and analyzing data to determine the performance of a pose measurement system in computing the pose (position and ...

    from 81.30 EUR VAT included

    from 75.98 EUR VAT excluded

    To selection
  • Standard Test Method for Evaluating the Point-to-Point Distance Measurement Performance of Spherical Coordinate 3D Imaging Systems in the Medium Range

    Standard [CURRENT] 2017

    ASTM E 3125:2017

    Standard Test Method for Evaluating the Point-to-Point Distance Measurement Performance of Spherical Coordinate 3D Imaging Systems in the Medium Range

    1.1 This test method covers the performance evaluation of laser-based, scanning, time-of-flight, single-detector 3D imaging systems in the medium-range and provides a basis for comparisons among ...

    from 105.90 EUR VAT included

    from 98.97 EUR VAT excluded

    To selection
  • IEEE Recommended Practice for Radar Cross-Section Test Procedures

    Standard [CURRENT] 2020

    IEEE 1502:2020

    IEEE Recommended Practice for Radar Cross-Section Test Procedures

    from 101.70 EUR VAT included

    from 95.05 EUR VAT excluded

    To selection
    • Note

    If you leave this page your selected items will not be added to the selection. What do you want to do next?

    Discard selection and go to the next page